ElVit-esphome_components/components/maidesite_desk

ESPHome Maidesite Desk Component

ESPHome component for controlling Maidesite desk controllers via their serial protocol.

Usage

What you need

• ESPHome compatible microcontroller (e.g. ESP32, ESP32-S2, ESP32-C3, ...)
• RJ12 cable (phone cable, RJ11 may also work)

Wiring

RJ12 connector pinning

Please double check this for your specific model!

pin	function
1	NC (pulled up)
2	GND
3	TX
4	VCC
5	RX
6	NC (pulled up)

Microcontroller pinning

ESP	desk
GND	GND
5V	VCC
GPIO3	TX
GPIO4	RX

Sometimes the desk controller does not supply enough current, then simply disconnet the VCC pin and plug in a micro-usb/usb-c cable into your ESP board.

Example ESPHome yaml code

external_components:
  - source:
      type: git
      url: https://github.com/ElVit/esphome_components/
    components: [ maidesite_desk ]

uart:
  - id: uart_bus
    tx_pin: GPIO3
    rx_pin: GPIO4
    baud_rate: 9600

maidesite_desk:
  id: my_desk

sensor:
  - platform: maidesite_desk
    height_abs:
      name: "Height"

number:
  - platform: maidesite_desk
    height_abs:
      name: "Height"
      mode: SLIDER

button:
  - platform: maidesite_desk
    stop:
      name: "Stop"
    step_up:
      name: "Step up"
    step_down:
      name: "Step down"
    goto_max:
      name: "Move to MAX"
    goto_min:
      name: "Move to MIN"
    goto_m1:
      name: "Move to M1"
    goto_m2:
      name: "Move to M2"
    goto_m3:
      name: "Move to M3"
    goto_m4:
      name: "Move to M4"

Examples

• basic, sufficient for most people: example_basic.yaml
• full with all features in use: example_full.yaml

Features

sensors entities

entity	description
height_abs	current height of the desk
height_pct	height in percent
height_min	minimal height
height_max	maximal height
position_m1	1st stored height
position_m2	2nd stored height
position_m3	3rd stored height
position_m4	4th stored height

number entities

entity	description
height_abs	current height of the desk
height_pct	height in percent

buttons entities

entity	description
step_up	move up desk by one step (~14mm)
step_down	move down desk by one step (~14mm)
goto_max	move up until stopped
goto_min	move down until stopped
stop	stop movement of desk
goto_m1	move to 1st stored height
goto_m2	move to 2nd stored height
goto_m3	move to 3rd stored height
goto_m4	move to 4th stored height
save_m1	save current height to 1th position
save_m2	save current height to 2th position
save_m3	save current height to 3th position
save_m4	save current height to 4th position

lambda methods

method	description
id(my_desk).step_up()	step_up desk by one step (~14mm)
id(my_desk).step_down()	step_down desk by one step (~14mm)
id(my_desk).goto_max_position()	move up
id(my_desk).goto_min_position()	move down
id(my_desk).stop()	stop movement of desk
id(my_desk).goto_mem_position(pos)	move to stored height pos
id(my_desk).save_mem_position(pos)	save current height to position pos
id(my_desk).goto_height(height)	move to specified height

Dev Notes

Jarvis reverse engineering notes

To see and send custom UART messages the following esphome code can be used:

esphome:
  ...
  includes: components/common_includes.h

uart:
  - id: uart_bus
    tx_pin: GPIO3
    rx_pin: GPIO4
    baud_rate: 9600
    debug:
      direction: BOTH
      after:
        bytes: 9
      sequence:
        - lambda: UARTDebug::log_hex(direction, bytes, ',');

text:
  - platform: template
    name: "UART message"
    id: uart_msg
    optimistic: true
    min_length: 0
    max_length: 100
    mode: text
    initial_value: "f1,f1,01,00,01,7e"

button:
  - platform: template
    name: "Send UART message"
    on_press:
      - uart.write: !lambda |-
          auto str = id(uart_msg).state;
          str = std::regex_replace(str, std::regex("0x"), "");
          str = std::regex_replace(str, std::regex(",| "), "");
          std::vector<uint8_t> out;
          auto ret = parse_hex(str.c_str(), out, str.length() / 2);
          return out;

To be able to use the regex command the file "common_includes.h" must be created in the directory "components".
The content of the "common_includes.h" must be:

#include <iostream>
#include <regex>
#include <string.h>

Sources

❤️ A big THANKS to Rocka84 for doing the main work, I've just forked this repo and modified some parts.
❤️ A big THANKS to shades66 for the minimal and easy to setup esphome config.
❤️ A big THANKS to phord/Jarvis for reverse engineering the UART interface and most control messages!
❤️ A big THANKS to OkhammahkO for collecting the scattered information at pimp-my-desk/desk-control!
❤️ Thanks to the whole home assistant community for sharing their knowlege and helping me to create this ESPHome component!