mirror of
https://github.com/maziggy/bambuddy.git
synced 2026-09-30 03:01:21 +02:00
maziggy
9500c046c0
Load and Unload in the AMS slot menu did nothing on an H2C with the switch fitted. The ams_change_filament command carries an optional extruder_id and Bambuddy never sent it. That is correct on every printer without the switch, and is what BambuStudio does there too -- each AMS is wired to one hotend, so the firmware works the target out for itself and an explicit value would only be a guess at something it already knows. Fit the switch and every AMS is bound to one of its two inlets instead, either hotend is reachable from any slot, and a command naming neither leaves the firmware nothing to act on. It was discarded in silence. Load now asks which hotend to feed, on the same terms as Bambu Studio: no preselection, so a stray Enter cannot feed the wrong one, and the hotend already fed from that very slot greyed out. Printers without a switch send a byte-identical command and still load in one click. A switch fitted but not yet set up -- any AMS still unassigned to an inlet -- refuses the load up front rather than publishing one the firmware will drop, mirroring DevFilaSwitch::IsReady, which likewise demands a switcher position on every AMS. Unload was addressed at the same time. It was aimed with tray_now, a single value for the whole printer, so on any dual-nozzle machine with both hotends loaded it unloaded whichever that field happened to name regardless of which slot's menu was used. It now names the slot and resolves the holding hotend from device.extruder.info, previously read for temperatures only. That resolution is gated on the printer having reported two extruders: single-nozzle machines do send the block, but nobody has read a single-nozzle snow value off the wire, and staking every X1C, P1S and A1 unload on an unverified encoding buys nothing where tray_now is already unambiguous. Both new state fields ride the WebSocket and are in the broadcast key, and both are computed in the REST status route as well -- that response is what the page has before any push arrives, and leaving them at their defaults would have told a correctly set-up machine that its switch was not set up. Verified on H2C-1, AMS-A slot 3: loaded and unloaded from each hotend in turn, all four correct. Covered by 18 MQTT unit tests, 4 status-dict tests, 7 integration tests and 6 component tests. Two known stragglers, both deliberately left alone. Load on an AMS-HT slot has never worked -- an HT unit is addressed by its unit id rather than ams*4+slot, which these endpoints do not accept -- so unload there keeps the printer-wide form it always used instead of gaining a slot it cannot name. And a slot's K-profile still follows the AMS's plumbing rather than the nozzle just loaded, so loading to the far hotend leaves the other one's calibration bound; that is the same per-nozzle problem the filament and K-profile redesign is scoped to fix.
React + TypeScript + Vite
This template provides a minimal setup to get React working in Vite with HMR and some ESLint rules.
Currently, two official plugins are available:
- @vitejs/plugin-react uses Babel (or oxc when used in rolldown-vite) for Fast Refresh
- @vitejs/plugin-react-swc uses SWC for Fast Refresh
React Compiler
The React Compiler is not enabled on this template because of its impact on dev & build performances. To add it, see this documentation.
Expanding the ESLint configuration
If you are developing a production application, we recommend updating the configuration to enable type-aware lint rules:
export default defineConfig([
globalIgnores(['dist']),
{
files: ['**/*.{ts,tsx}'],
extends: [
// Other configs...
// Remove tseslint.configs.recommended and replace with this
tseslint.configs.recommendedTypeChecked,
// Alternatively, use this for stricter rules
tseslint.configs.strictTypeChecked,
// Optionally, add this for stylistic rules
tseslint.configs.stylisticTypeChecked,
// Other configs...
],
languageOptions: {
parserOptions: {
project: ['./tsconfig.node.json', './tsconfig.app.json'],
tsconfigRootDir: import.meta.dirname,
},
// other options...
},
},
])
You can also install eslint-plugin-react-x and eslint-plugin-react-dom for React-specific lint rules:
// eslint.config.js
import reactX from 'eslint-plugin-react-x'
import reactDom from 'eslint-plugin-react-dom'
export default defineConfig([
globalIgnores(['dist']),
{
files: ['**/*.{ts,tsx}'],
extends: [
// Other configs...
// Enable lint rules for React
reactX.configs['recommended-typescript'],
// Enable lint rules for React DOM
reactDom.configs.recommended,
],
languageOptions: {
parserOptions: {
project: ['./tsconfig.node.json', './tsconfig.app.json'],
tsconfigRootDir: import.meta.dirname,
},
// other options...
},
},
])