The photo fired the moment layer_num reached total_layer_num. That edge is
where the printer *starts* its final layer, not where it finishes it: the
reporter's H2C capture shows it arriving at 92% with mc_remaining_time=2,
three minutes and seventeen seconds and one filament change before the print
actually ended, so the frame caught the toolhead mid-print over the model.
The trigger also latched _finish_photo_captured, which locked out both the
stage-22 and FINISH triggers for the rest of the print — so on firmware that
never reports an end-of-print filament unload (H2C and A1 Mini confirmed)
nothing could replace the bad frame.
Remove the last-layer trigger. The photo is now taken at the FINISH-state
trigger, which every model sends and which lands after the toolhead parks.
Since Bambu's end G-code drops the plate ~100mm just before that, restore the
framing before capturing: absolute G90/G1 Z to max_z_height + 10mm clearance,
settle, capture, then drop it back so the print is as reachable as the printer
left it. Absolute is the safety argument — that Z is a height the toolhead
occupied seconds earlier, so it is inside the travel limits by construction and
leaves the nozzle above the part, and it is unambiguous across model families
because Z is the nozzle-to-bed gap whether the bed moves or the toolhead does.
M211 is never touched (#2579). This is what #1145, #1397 and #1565 asked for.
The height is only trusted when two independent sources agree: the archive is
matched by the finished print's subtask_name by equality (not LIKE, so "Cube"
cannot resolve to "Cube v2"), and its layer count from the 3MF must match the
layer count the printer reported over MQTT. Matching on "most recent archive
for this printer" was not safe — on_print_complete pops the _active_prints
binding concurrently, and a print Bambuddy failed to archive would have
resolved to its predecessor. A wrong height is the one failure that could drive
the nozzle into the model.
The move is additionally skipped when the print height is unknown, when a queue
item is pending for the printer, when the printer has left FINISH, and when the
new finish_photo_restore_plate setting is off.
for every FINISH-state capture — which is what shipped the mid-print photo —
the bank is used only when the dispatcher recorded that it injected End G-code
into this print, since a SwapMod snippet may have ejected the plate. The flag is
handed over in two steps (mark_pending at dispatch, adopt at print start) so it
can never outlive its print: a job started from the slicer or SD card adopts
False rather than inheriting its predecessor's answer. Those prints also skip
the plate move outright, bank or no bank.
The bank now refreshes on mc_percent advances as well as layer changes, via a
new on_print_progress callback. Layer changes stop the instant the final layer
begins, which left the #1867 fallback frame stale by the whole length of that
layer; progress keeps ticking there and freezes before the End G-code runs, so
a swapped plate still cannot reach the bank. The last-layer throttle exemption
is dropped, since it would now fire a grab on every percent tick.
On the timelapse path the moment producer returns early, so the consumer does
the restore itself before its live-grab fallback — the documented usual outcome
on P1-series, where the video has not transferred by the time the notification
goes out and the shipped photo was of an already-dropped plate. The two waits
are now derived from the settle window and the video poll timeout rather than
hardcoded; at the old flat 75s that fallback was guaranteed to be cut off
mid-settle.
extract_max_z_height_from_3mf reads only a bounded prefix of the plate G-code,
since a sliced plate is routinely tens of megabytes and the header is ~40 lines.
It returns None for missing, unparseable, zero and negative values so callers
must treat "don't know" as such rather than defaulting.
The filament list is positional from the modal down to the CLI's
filament_N.json parts, but for a source that already carries slice_info the
requirements endpoint returns only the slots the plate consumes. A
MakerWorld model declaring four filaments and painting with slot 4 alone
therefore showed one dropdown, whose PETG pick the CLI bound to slot 1 —
slot 4 sliced with the profile baked into the source, and the print came out
PLA.
The endpoint now takes full_slots, which widens that answer to every
project slot with used_in_plate flags, and only the slice modal passes it.
Print-time AMS matching shares the endpoint and keeps the used-only list, so
it still asks for exactly the spools the job needs.
The Queue listing serialized each item by opening its 3MF and re-parsing
slice_info.config three times (print time, filament usage, bed type) on
every poll, per connected client, even for unchanged files. Add a single
combined extract_plate_metadata_from_3mf() cached by (path, plate_id,
mtime_ns, size); the three legacy helpers delegate to it. An unchanged
queue now does no repeat 3MF parsing.
Three bugs on the same PLA-model + PVA-support flow, discovered in
sequence:
(A) substitute_unused_plate_filaments inspected only object geometry
(per-object extruder metadata + paint_color triangles) so a support-
only slot was silently treated as "unused" and the user's PVA profile
got overwritten with slot 1's PLA.
(B) _extract_filament_info stripped filament_is_support==1 entries,
hiding PVA from unsliced source archive cards even when the project
explicitly configured it.
(C) --load-settings is authoritative over the source's project_settings.
config, and Bambu's shipped process presets ship enable_support=0
(supports are a per-print decision, not per-quality). So even with
(A) fixed, the sliced output had supports disabled and the PVA slot
loaded but never consumed. Inverts BambuStudio GUI's semantics where
the project overrides the preset.
Fixes:
- New extract_support_filament_slots_from_3mf reads enable_support +
support_filament + support_interface_filament from project_settings.
config; substitute_unused_plate_filaments unions it into the geometry-
derived set.
- _extract_filament_info returns all configured filament types + colours.
- New _patch_process_support_settings overlays four fields (enable_
support, support_filament, support_interface_filament, support_type)
from the source 3MF onto the picked process preset JSON before
--load-settings sees it. Deliberately targeted to what fixes#1881
without widening to a full project-over-preset merge.
extract_nozzle_mapping_from_3mf has a single-active-extruder shortcut
(added in #851 for #827) at threemf_tools.py:354 that runs before the
per-filament group_id mapping. It fires whenever
extruder_nozzle_stats reports exactly one extruder as active. On
multi-nozzle Bambu printers (H2D / H2D Pro / X2D / H2C) the slicer
under-reports the second extruder when its nozzle volume-type isn't
enumerated in the slice's profile (common with HT-AMS / High-Flow
asymmetric setups, e.g. HT-AMS feeding the right nozzle on an H2D):
['Standard#1', 'Standard#0'] even when both extruders are genuinely
used. sum(active_extruders) == 1 → every filament was force-assigned
to physical_extruder_map[active_idx], the authoritative group_id was
discarded, and the Filament Mapping panel showed both filaments
badged L with the auto-match hard filter blocking the wrong-nozzle
tray as "Type not found".
Bug is parser-side and model-agnostic, not gated on AMS hardware —
typical dual-AMS H2D slices contain ['Standard#1', 'Standard#1']
(sum==2), never enter the shortcut, and work fine. Physical extrude
routing was not affected (gcode + project_file nozzle_mapping path
from #1780 is authoritative). User-visible harm: wrong L/R badge and
no auto-match for the second nozzle.
Gate the shortcut on len(distinct_group_ids) <= 1 from
slice_info.config. The slice_info parse is hoisted above the shortcut
and reused by Priority 1, so the gate adds zero extra I/O. The gate
only narrows the shortcut — it can't widen the bug onto any
previously-working slice. Generalizes to H2C and any N-nozzle printer
for free (no per-printer branching).
The 3MF parser sums prediction + weight across every plate (#1593) so the
archive card can headline the whole project — correct for the card, wrong
for the completion notification of a single plate. The queue UI already
re-reads the 3MF per-plate at print_queue.py:272-285; mirror that for the
notification path so Discord / Pushover / email show the plate's actual
duration and grams instead of the project sum. Helper fails open on every
error path so a missing or corrupt 3MF can't block the notification.
Reporter on a multi-printer farm with 40+-plate runs needed to walk to
the printer with the right physical plate, but the queue and the
scheduling modal didn't surface curr_bed_type the way the archive card
already did.
New utils/threemf_tools.extract_bed_type_from_3mf helper (per-plate) so
both the queue API and the /plates endpoint can return per-plate values.
PrintQueueItemResponse.bed_type populated from archive.bed_type /
library_file.file_metadata['bed_type'] as the default, then overridden
per-plate via the helper when item.plate_id is set. /archives/{id}/plates
(and library equivalent) include bed_type in each plate object.
Per-plate accuracy matters because archive.bed_type is captured at
ingest as only the first plate's value (services/archive.py:235) -
a 40-plate 3MF mixing PEI + Engineering returns PEI at the archive
level for every plate. The helper re-reads the 3MF and returns the
truth.
Frontend: queue card meta row + PlateSelector per-plate row + PrintModal
header all render bed icon + canonical label via the existing
getBedTypeInfo() helper, same as the archive card.
The Slice dialog listed every process / filament preset regardless of
the chosen printer, and always defaulted to the first listed preset
rather than what the 3MF was prepared with (#1325).
Matching uses the slicer's own compatible_printers list for imported
(local) presets and falls back to the "@BBL <model>" name suffix for
cloud / standard presets. Compatibility-unknown presets are never
hidden.
Defaults: the printer and process dropdowns default to the preset
names embedded in the source 3MF's project_settings.config when those
presets are available; the per-slot filament and process pre-picks
prefer a printer-compatible preset, and switching the printer re-picks
any selection left incompatible.
- UnifiedPreset gains compatible_printers, exposed for the local tier
- plates endpoints return embedded_printer / embedded_process
- new frontend util slicerPrinterMatch.ts; extract_embedded_presets_from_3mf
- slice.otherPrinters added across all 9 locales
Step 0 empirical test on 2026-05-20 disproved the "CLI cannot re-slice a
3MF for a different printer" assumption: feeding an 18-color H2D-bound
Trent900.3mf to the X1C bundle via /slice produces valid X1C G-code in
1.8s, with bed (256x256), kinematics, nozzle count, machine_start_gcode,
and bed_exclude_area all coming from the target bundle.
- SliceModal: drop !printerMismatch from isReady; remove the banner and
the sourcePrinterModel / printerProfileName / printerMismatch state
entirely. Cross-printer slicing is now indistinguishable from a normal
slice; the picker already shows the target printer.
- Remove slice.printerMismatch from all 8 locales.
- API cleanup: drop source_printer_model from /library/files/{id}/plates
and /archives/{id}/plates responses, drop the field from
frontend/src/types/plates.ts (PlateMetadata + LibraryFilePlatesResponse),
delete extract_source_printer_model_from_3mf from threemf_tools.py and
its 6 unit tests. Zero remaining consumers.
- i18n discipline cleanup in SliceModal.tsx (same drop): strip every
inline English defaultValue / positional fallback from t() calls (22
sites). Add slice.bundle / slice.bundleNone / slice.bundleAllRequired
to all 8 locales — they had no entry in any locale file and were being
served from the inline English fallback for every non-English user.
- Tests: rewrite the mismatch-warning test to assert "no banner, Slice
enabled" when models differ (regression guard); delete 2 obsolete
tests covering gate states that no longer exist.
Five stacked slice-pipeline bugs that each made the modal's profile picker
theatrical for 3MF inputs:
(1) `_strip_3mf_embedded_settings` removed `model_settings.config` /
`slice_info.config` / `cut_information.xml` along with
`project_settings.config`. The CLI silently exited after
"Initializing StaticPrintConfigs" — exit 0, no result.json — and
Bambuddy masked the failure by re-running with embedded settings
and the source's bound printer. Strip removed from the dispatch
path entirely.
(2) Standard-tier preset stubs lacked the `type` field, so the CLI
rejected `--load-settings` with rc=-5 ("input preset file is
invalid") and the same masking fallback fired. Added
`_SLOT_TO_PROFILE_TYPE` so each stub carries the right
machine/process/filament discriminator.
(3) Sliced-archive cards listed every project-wide AMS slot (16+
swatches for a 2-color print). `slice_and_persist_as_archive` now
reads `filament_type` / `filament_color` from the sliced output's
`slice_info.config` (which `ThreeMFParser` already gates on
`used_g > 0`) instead of inheriting from the source archive.
(4) SliceModal had no warning when the picked printer profile didn't
match the source 3MF — the CLI rejects cross-printer slices
(rc=-16) and fell back to embedded settings, producing wrong-printer
g-code that errored at print dispatch. Plates response now exposes
`source_printer_model`; the modal compares against the picked
profile name and disables Slice + shows an inline warning on
mismatch.
(5) MakerWorld URL-paste resolver listed plate instances without
showing which printer each was sliced for (`/instances/hits`
omits compatibility info that lives on `design.instances[]
.extention.modelInfo`). The resolve route now joins both payloads
by instance ID and forwards `compatibility` + `otherCompatibility`
onto each hit; the MakerWorld page renders "Sliced for {primary}"
+ "Also marked compatible: ..." per row.
Tests: 6 unit tests for `extract_source_printer_model_from_3mf`, 1 for
filtered filament metadata via ThreeMFParser, 2 for makerworld resolve
compat-merge (happy path + missing modelInfo), 3 frontend SliceModal
tests for the printer-mismatch warning + Slice-disabled gate. New i18n
keys `slice.printerMismatch`, `makerworld.slicedFor`,
`makerworld.alsoCompatible` across all 8 locales.
The slice modal previously rendered exactly one filament dropdown and
silently truncated multi-color 3MFs to a single profile, producing wrong
colours on every multi-filament print. End-to-end fix across sidecar,
backend, and frontend.
Sidecar (orca-slicer-api / bambuddy/profile-resolver, separate commit):
- /slice accepts up to 16 repeated filamentProfile parts; slicing
service materializes each and joins paths with `;` for
--load-filaments.
- /profiles/bundled emits filament_type and filament_colour per leaf
so the bundled tier carries metadata into the modal.
Bambuddy backend:
- SliceRequest gains filament_presets: list[PresetRef]. Validator
accepts three shapes (multi-color array, source-aware singular,
legacy bare-int id) and lands them all on a populated array before
the route handler runs — fully backwards-compatible.
- SlicerApiService.slice_with_profiles takes filament_profile_jsons:
list[str] and sends one filamentProfile multipart part per profile
(in submission order) so the sidecar receives N profiles cleanly.
- New service slice_preview runs the sidecar's slice_without_profiles
against an unsliced project file's embedded settings, parses the
result's slice_info.config, and returns the canonical per-plate
filament list. Cached by (kind, source_id, plate_id, content_hash)
with LRU eviction at 256 entries, per-key asyncio.Lock prevents
thundering-herd; transient sidecar failures are NOT cached so they
retry naturally; parse failures ARE cached (deterministic property
of the input, no point re-running).
- /filament-requirements endpoint chain: slice_info.config (existing,
sliced files) → preview-slice (new, unsliced project files) →
project_settings.config + painted-face heuristic with 5% noise
threshold (sidecar-down fallback).
- threemf_tools gains extract_project_filaments_from_3mf and
extract_plate_extruder_set_from_3mf — the latter unions object
top-level extruder, per-part overrides, and painted-face quadtree
leaves (1-E nibbles in paint_color attrs of <triangle> elements
inside per-object .model files).
- Cloud preset listing no longer fetches per-preset detail (Bambu's
rate limit at ~10/sec returns 429 on every request for users with
50+ presets). Unified-listing dedup pass instead backfills metadata
cross-tier so a cloud entry that wins dedup over a same-named local
entry inherits the local's filament_type / filament_colour.
Frontend:
- SliceModal multi-step: plate-picker first when the source is a
multi-plate 3MF, then preset dropdowns. One filament dropdown per
AMS slot the plate actually uses, each pre-picked by metadata
match against user's local + standard presets via existing
colorsAreSimilar / normalizeColorForCompare utils.
- SliceModal-only tier priority is now local → cloud → standard
(was cloud → local → standard). Other consumers of /slicer/presets
keep the existing cloud-first order.
- Submits filament_presets array; backfills the legacy singular
filament_preset from the array's first entry for stale-tab
compatibility.
- i18n keys added across all 8 locales: slice.filamentSlot,
slice.tier.{local,cloud,standard}, slice.cloud.{notAuthenticated,
expired,unreachable}, slice.noPresetsForSlot,
slice.allPresetsRequired (en + de fully translated; six others
seeded with English copies pending native translation, matching
the project's existing flow).
Permissions: no new endpoint paths added. Preview-slice runs inside
/filament-requirements (LIBRARY_READ / ARCHIVES_READ) and multi-filament
dispatch runs inside POST /slice (LIBRARY_UPLOAD). No auth surface
widened.
Tests: 6 SliceRequest schema tests for multi-filament + legacy-new
precedence; 9 unit tests for slice_preview cache behaviour (LRU
eviction with lock cleanup, content-hash invalidation, concurrent
thundering-herd guard, no-cache-poison on transient sidecar failure);
15 unit tests for the two new threemf_tools helpers (5 + 10 cases
including the 60/40 painted-threshold regression pin); a multi-filament
wire-format test pinning the multipart part count + order; 22 frontend
SliceModal tests covering plate picker, multi-color render,
metadata-aware pre-pick, manual override, and the new tier order.
Auto-Print G-code Injection had two reviewer-reported bugs from the initial
ship:
1. Start snippets were prepended to the entire plate_X.gcode, landing
before the printer's own bed-heat / homing / nozzle-prime sequence —
so a Swapmod start snippet that assumed nozzle-at-temp ran on a cold
printer (pleite). Anchor injection at "; MACHINE_START_GCODE_END" so
snippets land where a slicer-side custom-start-gcode would. Files
without the marker keep prepend behaviour as a fallback with a
warning log.
2. Placeholders like "G1 Z{max_layer_z} F600" were written verbatim;
firmware parsed them as Z1 and crashed the head into the print on
tall models — real safety bug (DevScarabyte). Added a header parser
for the 3MF "; HEADER_BLOCK_START..END" block (lowercased keys,
[units] suffix stripped, spaces -> underscores) and a Prusa-style
{name} substitution pass over both start and end snippets before
injection. Supported placeholders: {max_layer_z} / {max_print_height},
{total_layer_number} / {total_layers}, {total_filament_weight},
{total_filament_length}, plus any other normalised header key.
Unknown placeholders are left verbatim with a warning — a typo never
silently expands to an empty string.
16 new regression tests across 4 new classes in test_gcode_injection.py
(anchored injection + missing-marker fallback, placeholder substitution
including alias resolution + unknown-pass-through, direct unit tests
for each new helper). All 2195 backend unit tests pass.
Wiki print-queue page updated with the supported placeholder list and a
{max_layer_z} safety callout for park moves.
Per-model start/end G-code snippets configurable in Settings (Workflow
tab). Queue items get "Inject G-code" toggle — scheduler injects
snippets into a temp 3MF copy before FTP upload. Supports Farmloop,
SwapMod, AutoClear, Printflow 3D and similar bed-clearing systems.
Original files are never modified.
Dual-nozzle H2D/H2D Pro: filament matching now respects nozzle assignments
from the 3MF file. Each AMS unit feeds a specific nozzle (L/R), and the
scheduler/frontend constrain matching to only trays on the correct nozzle.
Falls back to unfiltered matching when no trays exist on the target nozzle.
L/R badges shown in the filament mapping UI. Translated in en/de/ja/it.
Fix AMS slot config overwritten on startup: on_ams_change unconditionally
unlinked BL spool assignments on every MQTT pushall, then re-assigned them
sending ams_filament_setting without setting_id — clearing the printer's
filament preset. Now compares spool RFID identifiers before unlinking.
Fix BL spool detection false positives: removed tray_info_idx from detection
logic in both backend is_bambu_lab_spool() and frontend isBambuLabSpool().
Third-party spools using Bambu generic presets had GF-prefixed tray_info_idx
values, causing misidentification. Now uses only tray_uuid and tag_uid.
SQLite WAL mode with 5s busy timeout reduces "database is locked" errors.
The CodeQL cleanup in "Housekeeping" (2b11efd) bulk-narrowed except
clauses across 50+ files, breaking FTP uploads on ALL printer models.
ftplib.error_perm (550 errors) is not a subclass of ftplib.error_reply,
so diagnose_storage() CWD failures escaped the handler and prevented
STOR from ever executing — causing 100% upload failure and HTTP 500s
on /api/v1/archives/{id}/reprint and /api/v1/library/files/{id}/print.
FTP fixes:
- Remove diagnose_storage() from upload hot path
- Change all except (OSError, ftplib.error_reply) to
except (OSError, ftplib.Error) across bambu_ftp.py
Exception handling reverts (9 files):
- Revert narrowed except clauses back to except Exception in route
handlers and service code where broad catches are intentional
defensive programming (archive parsing, HTTP clients, 3MF/ZIP
processing, Home Assistant, firmware checks)
- Keep narrow exceptions only where safe (single-op blocks like
int(), file.unlink(), socket.close())
- Remove unused XMLParseError imports from archive.py, threemf_tools.py
Closes#287
Implement accurate per-filament usage tracking for Spoolman integration,
similar to OpenSpoolman v0.3.0. This replaces the previous single-spool
reporting with multi-material aware tracking.
Features:
- Parse G-code from 3MF files at print start to build per-layer,
per-filament cumulative extrusion maps
- Store tracking data in new `active_print_spoolman` database table
(survives server restarts for long prints)
- Report accurate partial usage when prints fail/cancel based on
actual layer progress and G-code data
- Add "Disable AMS Weight Sync" setting to prevent AMS percentage-based
weight estimates from overwriting Spoolman's granular tracking
- Add "Report Partial Usage for Failed Prints" toggle (only shown when
weight sync is disabled)
- Use Spoolman's filament density instead of defaults for mm-to-grams
conversion
- Prefer tray_uuid over tag_uid for spool identification
maziggy