Two faults behind the same kind of print: one that arrives without a
retrievable 3MF, which on an H2S is any job started from the printer's
own internal library.
Such an archive has no file_path, and Path("").parent is Path("."), so
every site that derived the archive's folder from it landed on the data
directory itself. The finish-photo capture spotted that and wrote to
<archive_dir>/<id>/photos instead. Nothing else did. The photo was
written in one place and looked for in another: reads 404'd, deletes
dropped the name and left the file, and the notification attachment
never found the image. Hand-uploaded photos worked only because upload
and read agreed with each other rather than with the capture. Give the
question one owner in utils/archive_paths and have all four sites ask
it. Lookups check the old shared location too, so photos already
uploaded there stay reachable; uploads now go where captures go.
Separately, the remain%-delta fallback that stands in for a missing 3MF
can charge nothing for several reasons, and did so without a word. The
AMS reading is coarse and, on the reporter's printer, noisy: it rises
mid-print, swings five points over a job, sits at 100% through a
36-minute print on a fresh spool, and goes negative on a nearly empty
one -- which the start-of-print gate rejects, dropping the only slot
that was printing. Two of their prints went uncounted for two different
reasons and both read as "no spools updated", which is also what a print
with nothing to charge prints. Name the slot and the two readings in
each case, on the Spoolman path and on the internal-inventory path,
which has carried the same gates since #1119.
The Spoolman path also had no notion of which slots the print used, so a
spool swapped into an idle slot mid-print reads as consumption and is
billed to whoever that slot is assigned to -- the fault #1269 fixed for
the internal tracker, still open here, and likeliest on exactly the
prints this fallback serves, where nothing else narrows the field. Use
the same three pieces of evidence it does: the print's mapping, its
mid-print tray changes, and the tray it started on. The last needs
storing, because the internal tracker's row is deleted before this runs
and a screen-started print has no mapping to fall back on -- hence a new
nullable column, and no backfill, since a row from before it existed has
nothing to say. Where no evidence exists at all, every slot is still
considered.
Both paths also treated tray_now == 255 as naming a slot. It does not:
it is the field's initial value, the fallback for an unparseable
reading, and what it reports with nothing loaded. Mapped as a tray id it
becomes (255, 1), so as the only evidence it excluded every real slot
and charged nothing at all -- this issue's own bug, arriving by a new
route. On the internal path that is live today; on the Spoolman path it
would have shipped with the guard above. The external holder reports 254
when it is genuinely in use.
The arithmetic is untouched: at one percent per step this cannot resolve
a small print, and pretending otherwise would be worse than saying so.
Brings the Spoolman writer up to parity with the internal-inventory
side, which has had this fallback since #1119. When a Bambu print
starts without a retrievable .gcode.3mf on the printer (typically an
unsaved BambuStudio project, subtask_name='Untitled'), Spoolman no
longer silently skips the print's filament consumption.
- ActivePrintSpoolman.filament_usage now nullable; new tray_remain_start
column captures per-slot {remain, tray_uuid} at print start.
- store_print_data: always snapshots remain, even when 3MF is present
(mirrors usage_tracker.on_print_start), so partial-3MF prints can also
fall back per-slot.
- report_usage: 3MF path stays primary; new _report_remain_delta_for_slots
handles slots the 3MF didn't cover via delta * Filament.weight / 100,
resolving the spool via the existing slot-assignment table.
- _report_partial_usage: same fallback for aborted no-3MF prints.
#1119 invariant preserved: per-slot, per-print, gated on a valid
start/current remain AND a resolvable Spoolman spool. Uses curated
Filament.weight (not MQTT's unreliable tray_weight) — same trick the
internal-inventory side uses.
Mid-print spool swap detected via tray_uuid mismatch → slot skipped.
Double-charge prevented via handled_global_tray_ids dedup.
Implement accurate per-filament usage tracking for Spoolman integration,
similar to OpenSpoolman v0.3.0. This replaces the previous single-spool
reporting with multi-material aware tracking.
Features:
- Parse G-code from 3MF files at print start to build per-layer,
per-filament cumulative extrusion maps
- Store tracking data in new `active_print_spoolman` database table
(survives server restarts for long prints)
- Report accurate partial usage when prints fail/cancel based on
actual layer progress and G-code data
- Add "Disable AMS Weight Sync" setting to prevent AMS percentage-based
weight estimates from overwriting Spoolman's granular tracking
- Add "Report Partial Usage for Failed Prints" toggle (only shown when
weight sync is disabled)
- Use Spoolman's filament density instead of defaults for mm-to-grams
conversion
- Prefer tray_uuid over tag_uid for spool identification
maziggy