A job kept the AMS mapping of the printer it was made for. Moved to a
location and picked by another printer, a tray of the same material in
another colour passed the fit check, so the job printed in that colour.
The scheduler now drops a stored mapping when it assigns a job by model
or location and matches the trays on the chosen printer, by type and
colour. Moving a job from a printer to a model or location clears its
mapping and the "Print Anyway" given for that printer.
A printer without an AMS whose external spool has no filament set gave
the matcher nothing to match, so such a job went out without a mapping
and the firmware rejected it with 0700_8012. Every filament now goes to
the external spool there.
Five X2Ds with no AMS, each printing from its external spool holder,
took a job sent to a named printer and refused the same job sent to
"Any X2D": the file uploaded, the firmware answered 0700_8012 "Failed
to get AMS mapping table", and the item failed after three attempts.
A named-printer job carries a mapping the frontend resolved at queue
time, so the scheduler's matcher never runs. A model-based job has no
printer until dispatch, so the matcher does run -- and could not see an
external spool on a dual-nozzle printer. _build_loaded_filaments derived
dual-nozzle status from ams_extruder_map, which is built from AMS info
bits, so a printer with zero AMS units reported an empty map; every
external spool got extruder_id=None, and the nozzle-aware hard filter in
_match_filaments_to_slots discarded it because None equals neither 0 nor
1. The mapping came back all -1, was cleared to None, and the print
command went out as use_ams:true with no ams_mapping and no
ams_mapping2 at all.
This is the backend half of #1257, which fixed the same logic in
useFilamentMapping.ts and left this copy behind. Mirror its inference:
a populated nozzles[1].nozzle_diameter, a non-empty ams_extruder_map, or
more than one vt_tray entry. Replaying the reporter's own push-status
now yields extruder 1 for Ext-L and 0 for Ext-R, and a nozzle-1
requirement resolves to [254] -- what their working named-printer
dispatch sent. Single-nozzle printers keep extruder_id=None; nozzles
always has two entries, so its length alone must not be the signal.
Also stop dispatching a job the firmware is certain to reject. When the
matcher ran, matched nothing, and the printer has no AMS, fail the item
with the filament and nozzle it wants instead of spending an upload and
two retries on it -- that path already ended in a failed item, just an
opaque one. With an AMS attached the firmware error still stands, since
there the user can load a spool and press Resume. Fail-safe like the
nozzle-diameter guard (#1899): every branch short of a positive finding
returns None and dispatches as before.
_apply_filament_overrides is extracted from _compute_ams_mapping_for_printer
so the message names the filament the matcher looked for rather than the one
the 3MF was sliced with.
Adds /library/variant-groups for declaring that several sliced files are
the same job for different printers, and a variants payload on queue
creation that turns such a set into one queue item with a candidate per
file.
The candidate set is validated as a set: one file per printer model, each
file sliced for the model it is offered as, and at least one model with
an active printer. A cross-model item deliberately holds no file of its
own, because print_queue.library_file_id is ON DELETE CASCADE and would
destroy the whole job when a single alternative is deleted.
Fixes internal printer-model codes never being resolved on queue create
and update: normalize_printer_model returns unknown input unchanged, so
the or-chain never reached the code map and a "C13" target matched no
printer and waited forever.
Skips candidates whose file is trashed or missing. Library deletes are
soft, and SQLite runs with PRAGMA foreign_keys off, so neither case is
covered by the schema; the hard-delete paths now also drop the rows.
Adds library_files.variant_target_model so a user can say which printer
a file without slicer metadata is for, kept out of file_metadata so the
assertion is never mistaken for parsed data.
Adds print_queue_variants: the candidate files a queue item may run, each
with its own model, plate, AMS mapping and nozzle mapping. The scheduler
walks them in priority order and takes the first whose model has an idle
printer, then folds that candidate onto the queue row before the
selection commit — so upload, archive creation, print history and reprint
keep seeing an ordinary single-file item.
Candidates are ordered least-attempted first, so a printer that accepts
the file and never starts hands the job to the alternative on the next
lap instead of spending the item's whole retry budget on the machine
that is wedged. The item-level DISPATCH_MAX_ATTEMPTS bound is unchanged.
An item whose candidate files have all been deleted is held pending with
an actionable reason rather than failing deep in the upload, and waiting
notifications name the job and every model it is waiting on.
maziggy