feat(spoolman-inventory): squashed feature work for rebase onto dev
Squashed all commits from feature/spoolman-inventory-ui onto a single commit
to enable a clean rebase onto dev. Original per-commit history preserved at
backup tag backup/spoolman-inventory-ui-prerebase-20260507-105721.
feat(spoolman-inventory): squashed feature work for rebase onto dev
Squashed all commits from feature/spoolman-inventory-ui onto a single commit
to enable a clean rebase onto dev. Original per-commit history preserved at
backup tag backup/spoolman-inventory-ui-prerebase-20260507-105721.
The SpoolBuddy "weigh-then-assign" workflow tried to configure an empty AMS
slot at assign time, but Bambu firmware silently drops ams_filament_setting
and extrusion_cali_sel for unloaded slots — the MQTT calls completed and the
modal closed, yet BambuStudio kept showing the slot as default-PLA forever.
assign_spool now detects an empty target slot (fingerprint_type empty) and
persists the SpoolAssignment without publishing MQTT, returning a new
pending_config flag so the frontend can swap "Assigned!" for "Slot will
configure when you insert the spool." on_ams_change watches for the slot
to load (state == 11, which fires for 3rd-party tags too even when
tray_type stays empty) and replays the deferred ams_filament_setting +
extrusion_cali_sel — including the printer-kp realignment that converts
PFUS-prefix cloud user presets to the P-prefix local-preset filament_id
the slicer actually accepts.
The full assign-time MQTT block was extracted into
apply_spool_to_slot_via_mqtt so both the assign endpoint and the
on_ams_change replay path use the same resolution logic; the helper takes
~270 lines of duplication out of assign_spool.
After assigning a spool to an AMS slot, the Bambuddy UI could show the
wrong filament preset (e.g. "Bambu PLA Matte" instead of "Bambu PLA
Silk") even though the printer was configured correctly.
Two bugs:
1. AssignSpoolModal (PrintersPage hover card path) never saved the slot
preset mapping to the DB, so the display fell back to the old/stale
mapping from a previous manual configuration.
2. AssignToAmsModal (SpoolBuddy path) constructed the preset name from
spool.material + spool.subtype ("PLA Silk") instead of using the
authoritative spool.slicer_filament_name ("Bambu PLA Silk").
Fix: the backend now saves the slot preset mapping in assign_spool()
after successful MQTT configuration, using slicer_filament_name as the
display name. This covers both frontend paths and ensures the correct
name is always stored.
Two bugs caused spool assignments to always configure AMS slots with
generic Bambu filament IDs (e.g. GFB99 "Generic ABS") instead of the
spool's actual slicer preset:
1. PFUS* IDs (cloud-synced custom presets) were blanket-rejected and
replaced with generic IDs in both assign_spool and configure_ams_slot
2. Generic fallback IDs (GFB99, GFL99, etc.) were treated as "good"
presets by the slot-reuse logic, making them sticky once set
New priority: spool's own slicer_filament > slot's non-generic preset
(same material) > generic fallback.
BambuStudio actively resets AMS slots configured with unrecognized PFUS*
(user-local) preset IDs. Replace PFUS* with generic Bambu filament IDs
(e.g. GFL99 for PLA) in both the slot configure and inventory assignment
endpoints. When the slot already has a recognized cloud-synced preset for
the same material, reuse it to preserve K-profile calibration.
Also fix fill level bar not showing for brand new spools (weight_used=0)
by changing the condition from weight_used > 0 to weight_used != null.
MartinNYHC